9/20/2023 0 Comments Signal web uiSun Sep 4 19:09:09 2022 daemon.err vuci: /usr/lib/lua/ubus/ui.lua:749: in function 'get_menus' Sun Sep 4 19:09:09 2022 daemon.err vuci: /usr/lib/lua/ubus/ui.lua:653: in function 'generate_dynamic_routes' Sun Sep 4 19:09:09 2022 daemon.err vuci: stack traceback: Sun Sep 4 19:09:09 2022 daemon.err vuci: /usr/bin/lua: /usr/lib/lua/ubus/ui.lua:653: attempt to index local 'boardInfo' (a nil value) ![]() Sun Sep 4 19:09:09 2022 daemon.err uhttpd: vuci: accepted login for admin from 172.16.1.107 Sun Sep 4 19:09:09 2022 kern.notice Authentication was successful from HTTP 172.16.1.107 Sun Sep 4 19:08:00 2022 daemon.err mdcollectd: Error while doing database backup Sun Sep 4 19:08:00 2022 daemon.err mdcollectd: SQLite error: source and destination must be distinct When I run the logread command I get the following: Neither of these fixed the issue I still have a broken web ui and the three lights flash constantly. Use the bootloader mode to flash the firmware back to a legacy version in this case R-00.02.06 - this allowed me to access the old web UI from which I re-flashed the firmware to R_00.07.02.4 with the keep settings button disabled. Downgrade the firmware back to R_00.07.02 via SSHĢ. I've had a quick browse of the forum and tried some of the suggestions including the following:ġ. The router now won't load the web UI after logon - it just says loading and constantly flashes the three mobile signal lights. T14:16:10.548Z Stderr: Removed symlink /etc/systemd/system//rvice. T14:16:10.476Z Getting value for install-parameter: -sync T14:16:10.476Z Getting value for install-parameter: T14:16:10.361Z PNID '' appears to be an FQDN using it for the hostname T14:16:10.360Z Getting value for install-parameter: See \"systemctl status rvice\" and \"journalctl -xe\" for details.\n'"Įrror executing start on service vmware-stsd. "localized": "An error occurred while invoking external command : 'Stderr: Job for rvice failed because the control process exited with error code. See \"systemctl status rvice\" and \"journalctl -xe\" for details.\n" "Stderr: Job for rvice failed because the control process exited with error code. "translatable": "An error occurred while invoking external command : '%(0)s'", See "systemctl status rvice" and "journalctl -xe" for details. Stderr = Job for rvice failed because the control process exited with error code. Err Failed to set unit properties on rvice: Unit rvice is not loaded. T14:25:46.581Z Failure setting accounting for vmware-stsd. Performing start operation on service vmware-stsd. Successfully started service vmware-sts-idmd T14:25:33.942Z Failure setting accounting for vmware-sts-idmd. Performing start operation on service vmware-sts-idmd. T14:25:32.415Z Failure setting accounting for vmcad. Performing start operation on service vmcad. T14:25:28.180Z Failure setting accounting for vmdird. Performing start operation on service vmdird. ![]() ![]() T14:25:25.083Z Failure setting accounting for vmafdd. Performing start operation on service vmafdd. T14:25:24.580Z Failure setting accounting for lwsmd. Performing start operation on service lwsmd. Then I run the following command service-control -start -all So I enable SSH through vCSA and access it, I find that the services vxpd and vsphere-ui are not running, I use the command service-control -statusĪpplmgmt lwsmd pschealth vmafdd vmcad vmcam vmdird vmdnsd vmonapi vmware-analytics vmware-cis-license vmware-cm vmware-content-library vmware-eam vmware-imagebuilder vmware-mbcs vmware-netdumper vmware-perfcharts vmware-postgres-archiver vmware-rbd-watchdog vmware-rhttpproxy vmware-sca vmware-sps vmware-statsmonitor vmware-sts-idmd vmware-stsd vmware-updatemgr vmware-vapi-endpoint vmware-vcha vmware-vmon vmware-vpostgres vmware-vpxd vmware-vpxd-svcs vmware-vsan-health vmware-vsm vsan-dps vsphere-client vsphere-ui When I try to access the address via chrome/edge I get 192.168.10.12 refused to connect, which means Stage 2 doesn't start at all as I have seen in many videos. Once the ova file is imported in workstation I am asked to access the URL. Host Identity : (A and PTR record created in windows server DNS Server). I have a windows server 2016 with AD and DNS, IP 192.168.10.10.įirst I imported vCSA ova file into workstation with the following configuration
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |